Simple and Fractional Distillation of a Binary Mixture

Introduction/Background

Distillation is a process that is present in many common liquids such as perfumes, or even alcoholic beverages. It is through distillation that it is possible to have liquor with high alcohol content. Fruit and plant material produce dilute ethyl alcohol when fermented, and through distillation the ferment is transformed into concentrated and purified ethanol. The process of distillation consists in purifying a compound by separating it from non or less-volatile material. This is done by converting a liquid into vapor, and then condensing it back into liquid form.

Get Help With Your Essay

If you need assistance with writing your essay, our professional essay writing service is here to help!

Essay Writing Service

 In fractional distillation, a fractionating column is added to the apparatus in between the stock mixture vial and the distillation head. This fractionating column contains several theoretical plates in which vapors that rise are collected in the condensate pool of each; this allows for all the intermediate residues to drip back into the stock mixture to be distilled again, making the distilled compound purer¹. The fractionating column also allows for compounds with a close boiling point to be better separated than with just a simple distillation. The separation of these compounds is only possible due to differences in boiling point and vapor pressure between the two compounds in the binary mixture. Once a liquid is heated, this substance only starts to evaporate, or reach its boiling point, once the compound’s vapor pressure becomes equal to the external pressure acting on the liquid.  The compound with the lowest boiling point starts to evaporate first, and collecting in the distillation head, its vapor molecules are then passed through the condenser, where upon cooling, the molecules condensate back into liquid form, therefore leaving a purified liquid compound.

Boiling point is determined by strength of intermolecular forces, molecular weight, surface area and hydrogen bonds, therefore giving each compound its own boiling point. Moreover, to fully understand distillation, it’s important to understand that mixtures obey Dalton’s Law and Raoult’s Law. Dalton’s Law² states that the vapor pressure of a mixture is equal to the sum of the partial vapor pressures of each compound in that mixture, and Raoult’s Law³ states that the partial pressure of a compound in an ideal mixture is equal to the vapor pressure of the pure compound at the same temperature, multiplied by the mole fraction. Another important concept to know when it comes to distillations is the term azeotropes. Azeotropes refer to a certain class of liquid mixtures that have a constant boiling point which may be higher or lower than the pure components and the liquid does not change composition when evaporating^4.

The aim of this experiment was to separate and purify cyclohexane and toluene from a 1:1 binary mixture using a fractional distillation, and to create a plot of the process using a temperature versus volume graph.

Experimental section

Chemicals

Results

Fractional distillation: Cyclohexane

Fractional Distillation (after changing collecting vials): Toluene

SAMPLE CALCULATIONS:

Percent Recovery for Cyclohexane During Simple Distillation:

Percent Recovery =(Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent Recovery for Toluene During Simple Distillation:

Percent Recovery =( Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

SAMPLE CALCULATIONS:

Percent Recovery for Cyclohexane During Simple Distillation:

Percent Recovery =(Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent Recovery for Toluene During Simple Distillation:

Percent Recovery =( Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

SAMPLE CALCULATIONS:

Percent Recovery for Cyclohexane During Simple Distillation:

Percent Recovery =(Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent Recovery for Toluene During Simple Distillation:

Percent Recovery =( Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

SAMPLE CALCULATIONS:

Percent Recovery for Cyclohexane During Simple Distillation:

Percent Recovery =(Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent Recovery for Toluene During Simple Distillation:

Percent Recovery =( Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

SAMPLE CALCULATIONS:

Percent Recovery for Cyclohexane During Simple Distillation:

Percent Recovery =(Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent Recovery for Toluene During Simple Distillation:

Percent Recovery =( Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

SAMPLE CALCULATIONS:

Percent Recovery for Cyclohexane During Simple Distillation:

Percent Recovery =(Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent Recovery for Toluene During Simple Distillation:

Percent Recovery =( Actual Yield/Theoretical Yield)x100%

Percent Recovery = (3.0 mL/3.5 mL)x100%

Percent Recovery =86%

Percent recovery calculations from fractional distillation
Cyclohexane:
Percent recovery = (Actual Yield/Theoretical yield) x 100%
Percent recovery = (3mL/3.5mL) x 100 = 85.7%

Toluene:
Percent recovery: Percent recovery = (Actual Yield/Theoretical yield) x 100%
Percent recovery: (2.6mL/3.5mL) x 100 = 74.2%

To have a standard measure in mL, the number of drops to equal 1mL were counted. It was concluded that 1mL =  30 drops.

Distillation curve for fractional distillation

Distillation curve for fractional distillation

Discussion:

In this lab, the main purpose was to separate a binary mixture of cyclohexane and toluene into their pure compounds. This was done successfully, but the amount of cyclohexane and toluene retrieved at the end did not equal the amount that the original mixture had. This is referred to as percent recovery, the percentage of an original substance recovered after the distillation has been completed.  The original binary mixture had 3.5mL of cyclohexane and 3.5mL of toluene, after distillation only 3mL of cyclohexane, and 2.6mL of toluene were recovered.  Meaning that the percent recovery for cyclohexane was 85.7% and for toluene 74.2%. The percent recovery for cyclohexane presents a good number and indicates that the experiment went as desired in the first part. For toluene, the percent recovery is lower than 80%, which indicates that there must have been an error during the experiment. A plausible explanation as to why the percent recovery for toluene was much lower than for cyclohexane might be due to adding aluminum foil to the distillation head when waiting for the toluene drops to start. This was done due to the experiment taking abnormally long, 33 minutes to be exact, to start distilling toluene after already collecting cyclohexane. This made the temperature rise rapidly from 25℃ to 70℃ in only 2 minutes, and was the only thing done differently from the first part of the experiment, which can explain the difference in percent recovery. Another factor into play was that the experiment was stopped due to the stock mixture being close to burning out. This might have been due to the rapid rise in temperature, which may have caused particles to escape the apparatus due to a faulty connection, or similar.

Find Out How UKEssays.com Can Help You!

Our academic experts are ready and waiting to assist with any writing project you may have. From simple essay plans, through to full dissertations, you can guarantee we have a service perfectly matched to your needs.

View our academic writing services

The graph in the lab manual combines both the cyclohexane and toluene distillation as we as combining simple and fractional distillation into one graph. This differs from this report’s graphs due to not obtaining the data from the simple distillation, and therefore only having fractional distillation graphs, as well as the data not being recorded in regular increments. This was due to a distraction when cyclohexane first started dropping into the receiver, therefore not capturing the start of it. While the toluene distilled incredibly fast, in about a third of the time from the cyclohexane, making it hard to take values at regular intervals. The shapes of the graph mainly match the graph from the lab manual, with exception of the temperature dropping at the end of the cyclohexane, and in the very beginning of the toluene distillation.

Conclusion

 The aim of this experiment was to separate and purify cyclohexane and toluene from a 1:1 binary mixture using a fractional distillation. This was proved to be mainly successful as in the end a mixture of cyclohexane and toluene were obtained, although the percent recovery for cyclohexane was higher than for toluene. The information from the data revealed that toluene indeed has a much higher boiling point than cyclohexane, as the distillation of toluene was only concluded at much higher temperatures than for cyclohexane. Furthermore, the information from the data obtained proved how the difference in boiling points between compounds is a key component for distillation to happen.

The techniques used in this lab are quite essential in the real world, especially in the oil industry. It is by fractional distillation that crude oil is broken down into gasoline, which powers the majority of commercial vehicles⁵. The understanding of this technique can help improve the amount and purity of distillate collected. In turn, this can decrease the amount of fossil fuels used, both by obtaining higher amounts of gasoline from a crude oil barrel, as well by decreasing the energy used to perform such distillations, as there are more than 40000 distillation units across the country.

Overall, the lab accomplished what it was set out to do, demonstrating the relationship between difference in boiling points and the distillation process.

References

1. Nichols, Lisa. “Organic Chemistry Laboratory Techniques”, LibreTexts, 2019. https://chem.libretexts.org/Bookshelves/Organic_Chemistry/Book%3A_Organic_Chemistry_Lab_Techniques_(Nichols)/5%3A_Distillation/5.3%3A_Fractional_Distillation
2. Dutton, F.B. “Dalton’s Law of Partial Pressures.”, Journal of Chemical Education Aug 1961. http://pubs.acs.org/doi/pdfplus/10.1021/ed038pA545.1
3. Kugel, Roger W. “Raoult’s Law: Binary Liquid-Vapor Phase Diagrams” Journal of Chemical Education 75.9. 1998
4. Clark, Jim. “Fractional Distillation of Non-ideal Mixtures (Azeotropes)”, LibreTexts, 2019. https://chem.libretexts.org/Bookshelves/Physical_and_Theoretical_Chemistry_Textbook_Maps/Supplemental_Modules_(Physical_and_Theoretical_Chemistry)/Equilibria/Physical_Equilibria/Fractional_Distillation_of_Non-ideal_Mixtures_(Azeotropes)
5.  Distillation and Filtration -Real life applications. Science Clarified, 2017. http://www.scienceclarified.com/everyday/Real-Life-Chemistry-Vol-2/Distillation-and-Filtration-Real-life-applications.html
6. Weldegirma, Solomon. Experimental Organic Chemistry: Laboratory Manual for CHM 2210L and CHM 2211L. University of South Florida. 2018