Design of a SET Based 4-bit ALU Using Proteus

Single Electron Transistor (SET) is a low-powered Nano device and as such it requires some sort of optimization at all levels to achieve a high-end performance. This paper will be presenting the design of a SET based 4-bit ALU using Proteus in view of its excellent potential for future Ultra Large Scale Integrated (ULSI) Circuits. The basic circuits required for this design such as Adder, multiplier and Comparator circuits will be designed & simulated using Proteus. However, the proposed logic design model is encouragingly operational at room temperature.

Get Help With Your Essay

If you need assistance with writing your essay, our professional essay writing service is here to help!

Essay Writing Service

Conversely, the SET-based ALU will be designed, simulated and optimized with incorporation of necessary and sufficient parameters in the feasible fabrication range in a hierarchical manner. It is expected that after simulation and design, we would be able to corroborate that a SET-based ALU is more efficient than CMOS-based ALU or its derivatives in terms of power consumption, delay and effectiveness. The analyses of the result could be performed if possible at 45nm technology node using Cadence EDA tool and of course, performance-based comparisons will be made with CMOS-based ALUs at percentages based on different parameters considered.

1.0 Introduction

The exponential increase in the density of integrated circuits predicted by Moore’s law has been mainly driven by reducing the dimensions of the semiconductor devices comprising these circuits. However, as semiconductor feature sizes shrink into the nanometer scale regime, device behavior becomes increasingly problematic as new physical phenomena at short dimensions occur, and limitations in material properties are reached. In effect, the SET technology circumvented the attendant problems common with CMOS technology which borders on speed and performance.

SETs are promising building blocks for future high-density and low-powered integrated circuits. In this paper, a SET-based 4-bit Arithmetic and Logic Unit (ALU) is discussed with necessary functionalities. Essentially, paper formulation is as follows: Section 2 talks about the design and simulation of a 4-bit ALU in details. Section 3 provides simulation results and section 4 is conclusion.

1.1 Single Electron Transistors (SETs)

A single-electron transistor (SET) is a sensitive electronic device based on the Coulomb blockade effect. In this device the electron flows through a tunnel junction between source/drain to a quantum dot (conductive island). Moreover, the electrical potential of the island can be tuned by a third electrode, known as the gate, which is capacitively coupled to the island. Figure 1 Below shows the basic schematic of a SET device. The conductive island is sandwiched between two tunnel junctions,[1] which are modeled by a capacitance (C_D and C_S) and a resistor (R_D and R_S) in parallel. (Source: Wikipedia).

Figure 1: The Basic Schematic of a SET device

The SET operates mainly as a switch and the fact that SETs may exhibit negative trans-conductance which allows the implementation of complementary circuits using transistors of a single type.

2.0 Design Methodology

2.1Design of a 3-bit ALU using Proteus: A case study

An ALU is a combinational logic circuit, meaning that its outputs will change asynchronously in response to input changes.

2.2Basic components

As a case study, I designed a 3-bit ALU to be able to explain a more complex 4-bit ALU. Basically, an ALU is made up of: an arithmetic and logic units. However, the basic components used to develop this sub units are electronic gates such as AND gate, OR gate, XOR gate, XNOR gate and the NOT gate. The truth table and circuit symbol of the aforementioned gates are shown below:

Figure 2: Basic Components of an Electronic Gates

More importantly, a typical ALU has sub circuitry in the child sheet of the design. It include the Addition/Subtractor, Array Multiplier, multiplexer and Logic unit blocks. This paper briefly explain all the sub-block in the child’s sheet of the design.

2.2.1 Adder/Subtractor Block

In digital circuits, an adder-Subtractor block is a circuit that is capable of adding or subtracting numbers in a binary system under the influence of a control signal (either 0 or 1).

2.2.2 Array Multiplier

Array multiplier is well known due to its regular structure. Multiplier circuit is based on add and shift algorithm. Each partial product is generated by the multiplication of the multiplicand with one multiplier bit. The partial product are shifted according to their bit orders and then added.

Figure 3: Description of the shift and add algorithm

2.2.3 Multiplexers

Multiplexer is a combinational circuit that has maximum of 2ⁿ data inputs, ‘n’ selection lines and single output line. One of these data inputs will be connected to the output based on the values of selection lines. Since there are ‘n’ selection lines, there will be 2ⁿ possible combinations of zeros and ones. So, each combination will select only one data input. Multiplexer is also called as Mux.

Figure 4: The Schematic diagram of a 4X1 Multiplexer

One of these 4 inputs will be connected to the output based on the combination of inputs present at these two selection lines. Truth table of 4×1 Multiplexer is shown below.

Selection Lines		Output
$S_{0}$	$S_{1}$	$Y$
0	0	$I_{0}$
0	1	$I_{1}$
1	0	$I_{2}$
1	1	$I_{3}$

From Truth table, we can directly write the Boolean function for output, Y as:

$Y = I_{0} \overset{̅}{S_{0}} \overset{̅}{S_{1}} + I_{1} \overset{̅}{S_{0}} S_{1} + I_{2} S_{0} \overset{̅}{S_{1}} + I_{3} S_{0} S_{1}$

The design interface of a 3-bit ALU is shown below which is able to perform addition, subtraction, multiplication and shifting operation. The picture below is just the parent sheet of the design. In the appendices section, this paper will show the full circuit.

Figure 5: The Display page of a 3-Bit ALU

2.3 Design of a 4-bit ALU using Proteus

Arithmetic and Logic Unit (ALU) is made of Arithmetic and Logic Units. This paper considers and designed sub-blocks such as Adder/subtraction block, 4-bit multiplier, Magnitude Comparator and Multiplexers using Proteus.

2.3.1 Operation table for a 4-bit ALU

Table 1: The truth-table of a 4-bit ALU

Inputs
$S_{2}$	$S_{1}$	$S_{0}$	$C_{in}$	$Function$	$Output$ Width
0	0	0	0	Addition	5-bit
0	0	0	1	Subtraction	4-bit
0	0	1	0	Multiplier	8-bit
0	0	1	1	Magnitude Comparator	3-bit
0	1	0	0	Logical Left Shifter	4-bit
0	1	0	1	Logical Right Shifter	4-bit
0	1	1	0	Right Rotator	4-bit
0	1	1`	1	Left Rotator	4-bit
1	0	0	0	Bitwise Inversion	4-bit
1	0	0	1	Bitwise AND	4-bit
1	0	1	0	Bitwise OR	4-bit
1	0	1	1	Bitwise XOR	4-bit
1	1	0	0
1	1	0	1
1	1	1	0
1	1	1	1

2.3.2Adder/Subtractor block

The logical gates discussed so far can be used for performing arithmetical functions like addition,

Subtraction, multiplication and division in electronic calculators and digital instruments. In the

Central processing unit (CPU) of a computer, these arithmetic functions are carried out by the

Arithmetic and Logic Unit (ALU). The logic functions used generally are AND, XOR and OR gates. A typical adder/ Subtractor which is implemented using logic gates is shown below.

Figure 6: A typical Adder/Subtractor Circuit

2.3.2.1 Full Adder

A full adder has three inputs and two outputs.It can add 3 digits (or bits) at a time. The bits A and B which are to be added come from the two registers and the third input comes from the carry generated by the previous addition. It produces two outputs; Sum and Carry-out. The truth table is shown below:

Table 2: The truth-table of a full adder

Input			Output
A	B	Cin	Sum	Carry-out
0	0	0	0	0
0	0	1	1	0
0	1	0	1	0
0	1	1	0	1
1	0	0	1	0
1	0	1	0	1
1	1	0	0	1
1	1	1	1	1

The resulting Boolean expression: $Sum, S = (A \overset{̅}{θ} B) \overset{̅}{θ} Cin and Carry - out = (A ∙ B) + (Cin ∙ (A \overset{̅}{θ} B))$

. The logic diagram of a FULL Adder is shown below.

Figure 7: Simulation of a full adder in proteus

2.3.2.2 Subtractor

This paper implements a subtractor circuit using the 2’s complement. For instance;

Table 3: The Truth-table implementing a subtractor circuit

A	B	Output (Y)
0	0	0
0	1	1
1	0	1
1	1	0

When $A = 0, Y = B$

and when $A = 1, Y = \overset{̅}{B}$

. Therefore, the Adder/Subtractor circuit is shown below:

Figure 8: Simulation of an adder/subtractor circuit in Proteus

2.3.3 4-Bit Comparator

Table 4: The truth-table for a 4-bit comparator

$A_{2}$	$A_{1}$	$B_{2}$	$B_{1}$	$A > B$	$A = B$	$A < B$
0	0	0	0	0	1	0
0	0	0	1	0	0	1
0	0	1	0	0	0	1
0	0	1	1	0	0	1
0	1	0	0	1	0	0
0	1	0	1	0	1	0
0	1	1	0	0	0	1
0	1	1	1	0	0	1
1	0	0	0	1	0	0
1	0	0	1	1	0	0
1	0	1	0	0	1	0
1	0	1	1	0	0	1
1	1	0	0	1	0	0
1	1	0	1	1	0	0
1	1	1	0	1	0	0
1	1	1	1	0	1	0

Equality Relationship ( A=B)

$X_{1} = 1 if A_{i} = B_{i} for i = 0, 1, 2, 3$

$∴ If A_{3} = B_{3} and A_{2} = B_{2} and A_{1} = B_{1} and A_{0} = B_{0} . Then, X_{3} = X_{2} = X_{1} = X_{0} = 1$

. In essence, the equality Condition is satisfied when EQ = 1.

Greater than relationship (if $A > B)$

This condition exist:

$If A_{3} > B_{3} \to A_{3} = 1 and B_{3} = 0$

$OR$ $If A_{3} = B_{3} and A_{2} > B_{2} \to A_{2} = 1 and B_{2} = 0 OR If A_{3} = B_{3}, A_{2} = B_{2} and A_{1} > B_{1} \to A_{1} = 1 and B_{1} = 0 OR If A_{3} = B_{3}, A_{2} = B_{2}, and A_{1} = B_{1}, A_{0} > B_{0} \to A_{0} = 1 and B_{0} = 0$

Greater Than (GT) = $A_{3} \overset{̅}{B_{3}} + X_{3} A_{2} \overset{̅}{B_{2}} + X_{3} X_{2} A_{1} \overset{̅}{B_{1}} + X_{3} X_{2} X_{1} A_{0} \overset{̅}{B_{0}}$

Less than Relationship (LT=1 if A<B)

This condition exist:

$If A_{3} < B_{3} \to A_{3} = 0 and B_{3} = 1$

$OR$ $If A_{3} = B_{3} and A_{2} = B_{2} \to A_{2} = 0 and B_{2} = 1 OR If A_{3} = B_{3}, A_{2} = B_{2} and A_{1} < B_{1} \to A_{1} = 0 and B_{1} = 1 OR If A_{3} = B_{3}, A_{2} = B_{2}, and A_{1} = B_{1}, A_{0} < B_{0} \to A_{0} = 0 and B_{0} = 1$

Less Than (LT) = $\overset{̅}{A_{3}} B_{3} + X_{3} \overset{̅}{A_{2}} B_{2} + X_{3} X_{2} \overset{̅}{A_{1}} B_{1} + X_{3} X_{2} X_{1} \overset{̅}{A_{0}} B_{0}$

Using Karnaugh map to simplify the greater than, less than and equal to relationship.

For A>B

$y_{1} = \overset{̅}{A_{2}} A_{1} \overset{̅}{B_{2}} \overset{̅}{B_{1}} + A_{2} \overset{̅}{A_{1}} \overset{̅}{B_{2}} \overset{̅}{B_{1}} + A_{2} \overset{̅}{A_{1}} \overset{̅}{B_{2}} B_{1} + A_{2} A_{1} \overset{̅}{B_{2}} \overset{̅}{B_{1}} + A_{2} A_{1} \overset{̅}{B_{2}} B_{1} + A_{2} A_{1} B_{2} \overset{̅}{B_{1}}$

$y_{1} = \overset{̅}{B_{2}} A_{2} + \overset{̅}{B_{1}} A_{2} A_{1} + \overset{̅}{B_{2}} \overset{̅}{B_{1}} A_{1}$

For A= B

$y_{2} = (A_{2} \overset{̅}{θ} B_{2}) * (A_{1} \overset{̅}{θ} B_{1})$

For A< B

$y_{3} = B_{2} \overset{̅}{A_{2}} + B_{1} \overset{̅}{A_{2}} \overset{̅}{A_{1}} + B_{2} B_{1} \overset{̅}{A_{1}}$

The equivalent representation of a 4-bit comparator in proteus is shown below:

Figure 9: Simulation of a 4-Bit Comparator in proteus

APPENDICES

References

Horea Gozar¹, Alexandru Chira², Örs Nagy³, Zoltán Derzsi. (2018, Jan 29). Medical Use of Finite Element Modeling of the Ankle and Foot. Journal of Inter-disciplinary Medicine.
Qin Li, Li Cai, Youjie Zhou, Gang Wu and Sen Wang. (2008). Design and Simulation of Logic Circuits by Combined Single-Electron/MOS Transistor Structures. IEEE Conference on Nano/Micro Engineered and Molecular Systems (pp. 6-9). China: IEEE. Retrieved October 4, 2018
Rathin Joshi, Yash Agrawal, Rutu Parekh. (2017). Design and Optimization of Single Electron Transistor base 4-Bit Arithmetic and Logic Unit at Room Temperature Operation. IEEEE International Symposium on Nanoelectronic and Information Systems (pp. 34-39). India: IEEE Computer Society. Retrieved October 10, 2018
Vaishali Rant, P.K. Dakhole. (2015). Design and Implementation of four bit Arithmetic and Logic Unit using hybrid Single Electron Transistor and Mosfet at 120nm Technology. International Conference on Pervasive Computing (ICPC). India. Retrieved October 1, 2018
Vaishali Raut, P. D. (2014). Design and Implementation of Single Electron Transistor N-Bit Multiplier. International Conference on Circuit, Power and Computing Technologies (ICCPCT) (pp. 1099-1104). India: IEEE. Retrieved October 8, 2018
Yongshun Sun, Rusli, and Navab Singh. (2011). Room-Temperature Operation of Silicon Single Electron Transistor Fabricated using Optical Lithography. IEEE Transactions on Nanotechnology, 10. Retrieved october 9, 2018

Share this: Facebook Twitter Reddit LinkedIn WhatsApp

Cite This Work

To export a reference to this article please select a referencing style below: